產品分類
Product Center
- 返回頂部
- 在線留言
- 掃碼更多精彩
聯系人：沈宇
電話：13815036227
地址：江蘇常州鐘樓區
名稱：缸徑規
點擊次數：1382
更新時間：2021-09-25 13:09:59
想了解更加詳細的產品信息，您還可以電話聯系： 13815036227
檢查零位調節
用零位設置工具向內壓缸徑表頂針，轉動表盤當大指針指向到零位時缸徑
表零位設置正確完成。
檢查高度調節
測量點的正確位置大約在活塞環邊緣下5mm 處。該高度可以通過旋轉螺絲眼上的螺母調節.
測量氣缸套
清潔缸套和掃氣口
放置測量缸套之工具，根據測量工具指示點測量缸套
在缸徑表與缸套處于垂直方向時讀取前點和后點的測量數據
安全預防措施
停機
阻斷啟動機械
關閉啟動空氣
嚙合盤車機關閉冷卻水
關閉燃油
關閉滑油
鎖定渦輪增壓器轉子
工具部件目錄
名稱 | 數量 |
木箱 | 1 |
零位調節工具 | 1 |
內六角扳手 | 1 |
保持架 | 1 |
缸徑表組件 | 1 |
定位鋼絲 | 1 |
伸展桿 | 5 |
Check of zero adjustment:
Press the tip of the dial gauge inwards by means of the zero setting tool the dial gauge is correctly.Zeroset when both the large hand points to the zero mark.
Check of height adjustment:
The correct position for the most top measuring point is approx 5mm below
upper edge of themost top poston ring the height may be adjusted by turning
fhe nuts on the eye of screw.
MEASURING OF CYLINDER LINER
Clean the cylinder liner and scavenging air ports
Position the measuring tool for measuring cylinderliner.Measure the cylinder liner according tothe points indicated on the measuring tool.
Take measurements in fore-and-aft and athwartship directions(see data).
SAFETY PRECAUTIONS/SIKKERHED
Stopped engine/Stoppet motor
Block the starting mechanism/Blokere forstartemekanismen
Shut off starting air supply/Luk for starteluft
Engage turning gear/ndryk tornegear
Shut offcooling water/Luk for kolevand
Shut offfuel oil/Luk for braendselsolie
Shut off lubrication oil/Luk for smoreolie
Lock turbocharger rotors/Turboladernes rotorer blokeres
Content of tool set
Item | Qty |
Wooden box | 1 |
Zero seting tool | 1 |
Internal hexagon spanner | 1 |
Supporting angle | 1 |
Measuring tool with dial gauge | 1 |
Wire with stops | 1 |
Extension bars | 5 |
